It is not necessary to power off your device, but if you would like to, you may simply unplug the power-in cable.To wake up your device, just tap anywhere on the screen.You may put the device to sleep manually by selecting the sleep button on the top left corner of the screen.EtcherPro is set to automatically go into sleep mode after a few minutes.The last EtcherPro of the stack should be plugged directly to the mains power socket.Plug the power extension lead to the input side of the leading EtcherPro, and then to the output side of the successive EtcherPro.To do this, you will need a male to female IEC C13/C14 power extension lead (min 10A rated) to connect one EtcherPro to another The plugged targets will be selected automatically, and the LEDs will turn whiteĭaisy-chaining (not released yet, power-only for now) Ĭonnecting up to 10 EtcherPro devices in a row Plug at least one drive into an available slot.Select the plugged in drive from the menu and press Select.From the Etcher menu, select Clone drive.Plug a drive you would like to clone into the first slot.Using a drive as source, and cloning it to multiple drives The plugged target(s) will be selected automatically, and the LEDs will turn white Plug at least one drive or device into an available slot.Enter the image URL of you would like to flash in the input field, and select OK.From the Etcher menu, select Flash from URL.Using an online image file as source to flash to one or multiple targets You may safely unplug the drives when flashing is complete.Once the flashing is complete, the LEDs will turn green for successfully flashed drives, and red for the failed ones.The LED of each slot will first blink purple for flashing and then green for validating.Select Flash, to begin the flashing process.The plugged target(s) will be selected automatically and the LEDs will turn white Select the image you want to flash from the file browser and select OK.From the Etcher menu, select Flash from file.Plug a drive that contains the image you would like to flash into the first slot.Using an image file as source to flash to one or multiple targets Select the network to which you want to connect, type the password and select OK.You can access the WiFi settings by selecting the WiFi icon at the top left corner of the screen.Please avoid using adaptors or extension leads, as this may damage the device or cause it to malfunction.The device should boot up automatically wait until you see the Etcher interface show up.Plug the AC power cable to the socket labelled POWER IN, and then to the mains outlet. ![]() On the back of the device, there are two groups of sockets, labelled as IN and OUT.EtcherPro is supplied with a mains power cable according to your region's plug standards.I also think a good idea would to if cloning a large drive to a smaller one, and if the partitions have enough unused space, for Balena Etcher to notify, then offer to reduce the size of the partition(s?) so they would work, keeping in mind that the Windows or Linux primary partition can’t have its beginning moved on the drive or additional steps will have to be taken to render it bootable again.Getting Started Setup Powering up the device Why does Balena Etcher not know this is a doable job and just clone it properly? I think that needs to be fixed. I’ve already copied both partitions to the SSD with GParted, which won’t boot, but both partitions fit with room left over. They boot and run fine in their reduced size, which is small enough to fit on the 512MB disk.īalena Etcher gives me an error message that the SSD is too small and refuses to do the very doable job. The remainder of the 1TB HD is unformatted. I’ve reduced the size of the working partition on the 1TB drive so both partitions are only 426MB, much smaller than the 512MB SSD will hold. I’m running Balena Etcher v 1.7.9 64 bit on Ubuntu 20.04. ![]() ![]() I’m trying to clone a 1TB windows system HD to a 512MB SSD.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |